Belt filter presses and recessed plate filter presses are both used to separate solids and liquids in slurries in a variety of applications, including the aggregate and mining industries.
BRIGHT supply professional and honest service.
The similarities between the two pieces of equipment end there, however. Besides design and how they work, belt filter presses and recessed plate filter presses differ in four key areas, which are outlined below.
Belt filter presses are a type of equipment used to separate solids and liquids in slurries.
The slurry is continuously fed to a delivery zone/box, then forced between two moving porous belts. The belts pass over and under rollers of various diameters, forcing the liquid to be squeezed out of the slurry while the solid cake material is retained between the belts. Increased pressure is created as the belt passes over rollers of decreasing diameter.
There are many designs of belt filtration processes, but all incorporate the following basic features:
Advanced designs provide a large filtration area, additional rollers, and variable belt speeds that can increase cake solids by a few percentage points.
The general mechanical components of a belt filter press include:
Belt filter presses have low to medium initial capital cost, with a smaller footprint for installation. Operating costs tend to be high due the need for a full-time operator and the use of chemical dewatering aids.
Maintenance costs are also expensive due belt and roller wear as well as failure from continuous movement of the tensioned belts between the rollers. Belts and roller bearings require frequent replacement, creating lower overall availability. Belt presses have a reputation of requiring frequent belt washing and are very sensitive to process variations.
Recessed plate filter presses are used to dewater slurries into manageable, “dry” cake material and to recover clear slurry liquid, typically water.
Recessed and membrane plate filter presses are among the oldest types of dewatering devices, having been used centuries ago to recover olive oil and grape juice. Today, filter press equipment is commonly used in aggregate and mineral processing waste slurry applications as well as mineral concentrate processing.
Typical filter presses are composed of a heavy-duty support framework holding a series of polypropylene plates with concave surfaces on each side of the plate. Synthetic filter cloths cover the plate surfaces completely to allow the initial separation of slurry liquid and solids. The plates are tightly clamped together with hydraulic pressure, creating a void space between the plate surfaces.
A high-pressure slurry feed pump forces the slurry material into the void spaces between the plates. The slurry solids are captured between the plates, while the liquid passes through the filter cloths mounted on the plate surfaces.
When no additional slurry can be pumped into the filter press, the slurry feed pump is stopped and the plates are separated, allowing the cakes to fall by gravity out of the press.
How a recessed plate filter press works.
Once all the filter cakes drop from the press, a new batch cycle can begin again with the press closing and clamping the plates together.
Depending on the type of material being dewatered and the size of the filter press equipment, the cycle time can vary from as short 10 minutes up to several hours or more.
To handle large volumes of slurries — up to 100 tons per hour of dry material, modern filter presses can be very large and require a large space for installation. Common filter press plate sizes today can be up to 8' wide by 8' tall (2.5m x 2.5m) or larger. The up-front investment for a recessed plate filter press can be high due the size of the equipment and the required support structure.
Recessed plate filter press operating costs are low due to several factors:
Because the slurry material is captured completely between the filter plates, very high dewatering pressures (up to 225 psi or higher) can be applied to the slurry. The high dewatering pressures produce the highest cake solids concentration possible of any mechanical dewatering equipment.
The key differences between a belt filter press and recessed/membrane plate filter press include:
A belt filter press is operated as a continuous process.
The slurry being dewatered flows into the feed box while the filtrate drains through the filter belts, with the dewatered cake continuously discharging from the end of the press.
The benefit of a continuous system is no requirement for a surge or buffer tank prior to the belt press.
A recessed or membrane plate filter press operates in a batch mode.
The slurry flow at the beginning of each cycle is very high because the chambers between the plates are empty. As the chambers fill, the slurry flow rate decreases until very little additional slurry can be pumped into the press. At that time, the pump is stopped to allow the cakes to be discharged out of the press. Once the cakes all discharge, a new cycle can begin.
Because of this batch nature of the plate press operation, a surge or buffer tank is required to accumulate the slurry while the slurry feed pump flow is low or stopped.
Belt presses require the use of a chemical flocculent to attract the fine solid particles in the slurry to agglomerate into larger particles that will drain water easier.
In most cases, the amount of chemical added is directly related to how dry the dewatered cakes eventually become at the discharge of the belt press.
Plate presses typically do not require any chemical additives to aid dewatering because the slurry material is forced with a feed pump into a closed space between the filter plates. Much higher dewatering pressures can be generated in the plate press, resulting in drier cakes.
In general, for any given type of slurry, a plate press will be able to attain 5-10% lower moisture cakes compared to a belt press.
Belt presses require full-time operators due to their inherent sensitivity to process changes and the need to make routine adjustments to optimize dewatering efficiency.
Plate presses can be fully automated, so they require only periodic monitoring. The slurry feed pressure and flow are continuously monitored on a plate press, allowing the control system to automatically adjust the dewatering cycle length to maintain optimum dewatering efficiency when normal process changes occur.
Typical maintenance cost for a belt press will be higher compared to a plate press primarily due to the higher number of continuously moving parts on a belt press.
The belt press uses two continuously moving filter belts that are driven and directed by 15-20 rollers. The rollers and roller bearings are exposed to the fine slurry particles as well as the filtrate that drains through the belts. This causes continual buildup of solids on the rollers and belts, which causes abrasion as well as overall corrosion, eventually requiring replacement of the rollers and belts.
The entire belt press must be cleaned periodically to prevent excessive buildup damage and to minimize abrasion and corrosion. The cleaning and maintenance repairs required on a belt press cause loss of operating time, lowering the overall efficiency.
The plate press operation involves very limited movement of the filter press components. Once a cycle for very shorts periods of time (typically only a few minutes), the filter plates are closed to begin a new cycle and opened to discharge the cakes. Therefore, very little wear occurs from the limited movement of the plates, typically resulting in much lower maintenance cost. Periodic cloth cleaning may be required, but this is dependent on the cloth material and the type of material being dewatered.
When deciding between a belt filter press and a recessed plate filter press, you should consider the long-term costs vs the upfront costs. Belt filter presses may require less capital cost, but lifetime maintenance costs for repairs and chemicals can add up. On the other hand, recessed plate filter presses have very little lifetime cost, as they don't require a full-time operator or chemical additives and require less maintenance.
Tech Team · Kintek Solution
Updated 6 months ago
For more information, please visit filter press plates.
A recessed plate filter press is a type of filtration equipment used to separate solids from liquids, commonly employed in industries such as chemical processing, wastewater treatment, mining, and food production. It operates by compressing a series of recessed plates together, forming chambers where slurry is pumped in. The liquid passes through filter cloths, leaving the solid material (filter cake) trapped within the chambers. This equipment is known for its high efficiency, ability to handle large volumes, and suitability for high-pressure filtration. The design of the recessed plates allows for easy removal of the filter cake and efficient cleaning, making it a versatile and durable solution for solid-liquid separation.
Definition and Functionality:
Components and Design:
Operation Process:
Applications:
Advantages:
Considerations for Purchasing:
Comparison with Other Filter Presses:
In summary, a recessed plate filter press is a robust and efficient solution for solid-liquid separation in various industries. Its design, operation, and versatility make it a valuable piece of equipment for applications requiring high-pressure filtration and large-scale processing. When selecting a recessed plate filter press, it is essential to consider factors such as material compatibility, capacity, and automation to ensure optimal performance and cost-effectiveness.
Need a reliable solution for solid-liquid separation? Contact our experts today to find the perfect recessed plate filter press for your needs!
Hydraulic Diaphragm Lab Filter Press for Laboratory Filtration
Hydraulic diaphragm lab press filter is one type lab scale filter press, it takes small footprint, and higher pressing power.
Heated Hydraulic Press Machine with Heated Plates for Vacuum Box Laboratory Hot Press
Enhance your lab's precision with our lab press for vacuum box. Press pills and powders with ease and precision in a vacuum environment, reducing oxidation and improving consistency. Compact and easy to use with a digital pressure gauge.
Electric Lab Cold Isostatic Press CIP Machine for Cold Isostatic Pressing
Produce dense, uniform parts with improved mechanical properties with our Electric Lab Cold Isostatic Press. Widely used in material research, pharmacy, and electronic industries. Efficient, compact, and vacuum-compatible.
Heated Hydraulic Press Machine with Integrated Manual Heated Plates for Lab Use
Efficiently process heat-pressing samples with our Integrated Manual Heated Lab Press. With a heating range up to 500°C, it's perfect for various industries.
Manual Cold Isostatic Pressing Machine CIP Pellet Press
Lab Manual Isostatic Press is a high-efficient equipment for sample preparation widely used in material research, pharmacy, ceramics, and electronic industries. It allows for precision control of the pressing process and can work in a vacuum environment.
Electric Split Lab Cold Isostatic Press CIP Machine for Cold Isostatic Pressing
Split cold isostatic presses are capable of providing higher pressures, making them suitable for testing applications that require high pressure levels.
Cold Isostatic Pressing Machine CIP for Small Workpiece Production 400Mpa
Produce uniformly high-density materials with our Cold Isostatic Press. Ideal for compacting small workpieces in production settings. Widely used in powder metallurgy, ceramics, and biopharmaceutical fields for high-pressure sterilization and protein activation.
Laboratory Hydraulic Press Lab Pellet Press Machine for Glove Box
Controlled environment lab press machine for glove box. Specialized equipment for material pressing and shaping with high precision digital pressure gauge.
Automatic Laboratory Hydraulic Pellet Press Machine for Lab Use
Experience efficient sample preparation with our Automatic Lab Press Machine. Ideal for material research, pharmacy, ceramics, and more. Features a compact size and hydraulic press functionality with heating plates. Available in various sizes.
Heated Hydraulic Press Machine with Heated Plates for Vacuum Box Laboratory Hot Press
The lab press for vacuum box is a specialized piece of equipment designed for laboratory use. Its main purpose is to press pills and powders according to specific requirements.
Automatic Lab Cold Isostatic Press CIP Machine Cold Isostatic Pressing
Efficiently prepare samples with our Automatic Lab Cold Isostatic Press. Widely used in material research, pharmacy, and electronic industries. Provides greater flexibility and control compared to electric CIPs.
Vacuum Hot Press Furnace Machine for Lamination and Heating
Experience clean and precise lamination with Vacuum Lamination Press. Perfect for wafer bonding, thin-film transformations, and LCP lamination. Order now!
Laboratory Hydraulic Press Split Electric Lab Pellet Press
Efficiently prepare samples with a split electric lab press - available in various sizes and ideal for material research, pharmacy, and ceramics. Enjoy greater versatility and higher pressure with this portable and programmable option.
Manual Lab Heat Press
Manual hydraulic presses are mainly used in laboratories for various applications such as forging, molding, stamping, riveting and other operations. It allows the creation of complex shapes while saving material.
Vacuum Hot Press Furnace Heated Vacuum Press Machine Tube Furnace
Reduce forming pressure & shorten sintering time with Vacuum Tube Hot Press Furnace for high-density, fine-grain materials. Ideal for refractory metals.