There are different rotor body styles. Most common are 3-bar and 4-bar rotors. This example is a 4-bar rotor that can be operated in the following two operation modes:
If you are looking for more details, kindly visit our website.
The inlet opening defines the overall feed-size. As a rule of thumb it is recommended that the maximum feed size is 80% of the inlet opening width.
A chain curtain prevents rocks being ricocheting back ensuring operator safety.
The impact wall is typically hinged and can be adjusted hydraulically. The apron is typically armored with replacedable impact plates. Some crusher types need to replace the entire impact wall once it is worn out.
Every rock is different even if it is the same type of rock. There is soft limestone and there is hard limestone. Please consult a crushing expert to verify your application.
This article was originally published in Dry Bulk magazine.
Before selecting an exact crusher, it is important to first consider what crushing technology is needed for the feed material. The two main methods used for crushing are fracture by energy or impact and compression or shear breakage. From an operating costs perspective, horizontal shaft impactors (HSI) are feasible in low abrasive and typically soft material applications.
Even from a CAPEX perspective, the HSI’s high throughput capacity can make it an interesting option in some cases. Barmac vertical shaft impactors (VSI), by virtue of being an impact crusher, can also be economically feasible with rather abrasive feed material. This is especially the case when crusher duty is focused on improving product quality in aggregates applications, or the target is to reliably produce -2 mm materials from soft to medium rock.
With medium-to-hard rock or ore that also has abrasive qualities, a compression crusher is often the most economical choice, especially in cases where a high reduction ratio is required. Once the first choice of technology is determined, other factors then need to be evaluated.
The primary crushing stage generally breaks down the material into pieces of max 200 – 300 mm. The aim is to achieve the right balance between feed size (capacity) and throughput (speed). Reaching this balance is important, as focusing on one aspect, while neglecting the other, could lead to an unsuitable choice of equipment. For example, focusing on accepting a large feed size could mean ending up with an oversized and hungry crusher that can handle more material than the plant can provide. Certain adaptations are possible, such as adjusting the machine settings or using a special liner to re-size the crushing chamber, but it is still important to choose a machine with a chamber size range that best fits the application.
Another factor that needs to come into consideration is machine reliability. As with most equipment, there is a trade-off between initial investment costs and long-term operational costs and reliability. As a rule of thumb, the higher the production requirements and the longer the equipment is set to operate, the more important reliability and low operating costs are.
For example, primary gyratory crushers (based on hydraulic floating shaft technology) are often the first choice of larger mining projects with a throughput of tph or more. Although these crushers demand a relatively high initial investment, they offer payback in the form of better total plant production and a lower operating cost per unit.
There are jaw crushers which carry lower upfront costs and are often preferred by small-to-medium size mining operations. Jaw crushers work well for reasonably hard and abrasive feed material and can handle a large feed size. Maximum throughput, however, is typically only tph even with the biggest units. When processing sticky materials with low-to-medium hardness, or if there are restrictions on installation headroom, the addition of a primary sizer can be helpful.
Also, there are cone crushers which are not generally used for primary crushing, but there are some notable exceptions, such as gravel plants, river gravel or screening the feed to eliminate over-sized material.
If choosing the right crusher is the first big decision, the second one is selecting the right wear liners to get the most out of the producing asset. Producers often reorder the same liners that came with their initial purchase, not realizing that liners play a significant role in the overall performance of crushing equipment and can make a big difference to the bottom line. Optimizing the liner profile can affect the quality and size of the end-product and allow the crusher to work more effectively.
For example, if a cone crusher is not producing the desired end product size, changing or adapting the bowl liner and mantle will bring different results. Similarly, new conditions can be created in the cavity and chamber of the primary gyratory crusher by adjusting the angle, liner alloy or thickness of the mantle and concave liners.
To get the best results when changing wear parts, it is recommended to consult a process expert who can carry out simulations in the lab and base their decisions on data.
Since liners are worn down by constant contact with the ore, they need to be changed regularly, which can be a big part of the operating costs. To keep costs in check, analyzing the crusher chamber and selecting liners with the right profiles, thickness and alloy grade to last as long as possible, is recommended.
Typically, liners are made from a low-grade manganese steel as a base offering. They can also be engineered with different manganese grades or from alloy steel or high chrome white iron, to maximize wear life and/or increase fatigue resistance.
Metso’s longer-life range of liners (MX series) is made with hybrid materials and represents a step up in liner lifetime. They have been shown to double the wear life compared to standard manganese steel liners in many applications.
Jiafu supply professional and honest service.
Exploring improved crusher performance, such as with a chamber optimization program, is the best option for taking crusher efficiency to the next level. It is a multi-step process which includes gathering data, running simulations and using expert analysis to look at options. From this process, it is possible to create tailor-made solutions and customer-designed wear parts that suit specific processes, applications and equipment, regardless of the brand.
When the chamber is working optimally, it is possible to achieve up to 30% reduction in energy consumption depending on the application, leading to a lower cost per ton and more sustainable operations. Wear parts can last two to four times longer, reducing the number of liners consumed, as well as resources needed to manufacture and transport them, thus further contributing to sustainability. Longer wear life also means fewer stops in production and fewer change-outs, which in turn also boosts both profitability and safety.
A chamber optimization program is not a one-off effort but rather an ongoing monitoring and improvement program. For example, the development of the liners might start with wear life improvement and continue with tweaking the design to maximize crusher throughput. Moreover, production targets and ore properties at a site can change over time and create an opportunity for further liner development. Each customer journey is unique, and chamber optimization can be especially beneficial for high-volume production sites and in situations where the raw feed characteristics have changed.
Choosing the right crushing technology, machine and liners are all important steps to take. However, every business wants its crushing equipment to have the longest life possible and this can be a real challenge when operating under harsh conditions. There are several ways to further extend lifetime, maximize performance and achieve a reduction in overall crushing costs through proper maintenance.
As part of a regular maintenance program, it is recommended to keep a constant eye on the crusher’s performance through regular inspections. These should include checking the condition and cleanliness of the hydraulic power units, hydraulic oil tank levels, oil temperatures, cooling fans and oil pressure levels, crusher noise levels, bearing temperatures, crusher vibrations, feed distribution, feed level and electric power draw amongst others.
Customers often find it valuable to get more thorough and specialized inspections at pre-set intervals, such as the hr operating mark. These inspections often include a review of key wear components and additional verification of critical spare components. Wear replacement inspections are useful to have and involve an inspection of the heads and bowls or concaves and mantle, as well as other components such as bushings, eccentrics, MPS and pitmans, depending on the crusher being inspected.
At an operational level, another often overlooked good practice is the assessment of the size of the rocks entering the feed. Oversized feed could lead to blockages in the crusher cavity which can cause bottlenecks to the entire process and result in unplanned downtime. There are different ways of addressing this issue, but the solution often lies in making improvements to the current drill and blast program.
It is essential that shutdowns come in on-time, on-budget and with minimal downtime. A good shutdown optimization program covers all elements of a shutdown, from start to finish. This includes a site evaluation and shutdown planning, as well as the actual execution of the shutdown.
Shutdown optimization typically begins with experts observing and analyzing the crusher relining process and coming up with improvements related to factors such as preparation analysis, concave replacement method (best practices), tooling, training, and safety. A more involved but highly effective time and motion study, often called a single minute exchange of dies (SMED) analysis involves capturing all the actions taken during a shutdown on video, documenting the tasks from start to finish, and creating a timeline with thousands of image and data points for analysis.
Expert support can then make recommendations to help improve the overall workflow and execution of the shutdown event, including removing non-critical tasks and idle periods, introducing better planning and coordination, and determining the optimal sequence of steps.
In a Chilean mine, for example, one time and motion study helped to reduce shutdown time from 100 to just 56 hours. Similar results were achieved in Finland, where mantle replacement times were cut in half, and the duration of a full reline was similarly shortened.
The industry is quite rapidly moving from a reactive to a preventive approach to crusher care, backed up by data analysis. Connectivity adds an extra layer of support that enables preventive maintenance and troubleshooting. The data from sensors monitoring the critical functions of equipment is collected and used to generate trend reports that can warn of upcoming issues in time to prevent production stops or safety risks.
Connectivity also enables remote troubleshooting — an excellent complement to on-site crushing services that lets operators access whatever expertise they need without having to physically bring a specialist out to the site.
More and more customers are demanding reliable analytics services and the ability to resolve issues remotely and efficiently, with access to global experts. Metso Performance Centers for example, use advanced digital tools, and connect global experts to bring together data, knowledge and global expertise to improve the reliability, safety, availability and operational performance of crushing and processing equipment. These improvements can lead to substantial improvements to a site’s profitability.
Many who are familiar with the techniques for selecting crushing equipment believe that it is possible to make a selection merely based on calculations. However, theoretical conclusions must always be counterbalanced by practical experience with operating factors, as well as the maintenance and economic aspects of a site.
From the choice of crusher and wear parts to long-term crusher care, considering all elements can help to make the right decisions, resolve issues and ensure the company gets the very best out of the equipment.
About the authors
Dusty Jacobson began his career in the mining and aggregates industries in after obtaining a BSc in Mechanical Engineering. Over his 20 years with Metso, he has held roles in research, design, sales and product development. His current role is director of process engineering for crushing equipment and plants.
Stuart Baillie has a bachelor’s degree in mechanical engineering and has been in the crushing business in Metso for 20 years. Originally from the UK, Stuart relocated to Australia in . He is currently the regional support manager for mining crusher wears for Asia-Pacific and India.
For more information, please visit Horizontal Shaft Impactors.