The PCB manufacturing process transforms design files such as Gerber/ODB++/IPC-, netlists, and drill files into a physical circuit board.
JYN are exported all over the world and different industries with quality first. Our belief is to provide our customers with more and better high value-added products. Let's create a better future together.
It begins with product conceptualization, schematic entry, layout design, and production file generation.
The bare board is fabricated once the printed board design files are finalized. Next, the components are assembled on the board, followed by comprehensive functionality testing.
The PCB manufacturing commences after receiving the design files from a PCB designer or an electrical engineer. The files include:
This stage involves:
Download our eBook to learn how to design a manufacturable PCB.
With the increasing miniaturization of electronic components, fabricators primarily rely on laser direct imaging (LDI) for precise circuit patterning.
Here are the steps involved in LDI:
The LDI workflow is shown in the image below:
Etching is a crucial step in the PCB manufacturing process, where the excess copper (non-circuit copper) is removed from the board to reveal the desired circuit pattern.
It typically takes place in a conveyorized develop, etch, and strip line. Here, the board moves through the chamber while being sprayed with the various chemicals to ensure consistent developing and etching to achieve the desired results.
Key parameters to monitor during etching include:
Proper control of these factors is essential for achieving precise and clean circuit patterns on the PCB.
In this process, the residual photoresist is etched away from the copper surface. The process involves dissolving caustic pellets (chemical agents) in water combined with a high-pressure water rinse, which breaks down and washes away the remaining photoresist.
Once all layers are cleaned and prepared, we perform a post-etch punch to ensure precise layer-to-layer registration. Using alignment targets on the inner layers, the boards are placed into an optical punch machine that accurately aligns both the inner and outer layers.
Following this, inspection is carried out through visual scanning of the board surface using an automated optical inspection (AOI) system. The circuit board is illuminated using various light sources, while high-definition cameras capture detailed images. The AOI system then analyzes these images to verify accuracy and detect any defects.
Here, the copper circuit pattern is coated with an alternative oxide coating, primarily used as an adhesion promoter. It also helps prevent oxidation and corrosion of copper.
Lamination is the process of bonding copper foil, prepreg, and inner layer cores under controlled temperature and pressure to form a multilayer PCB.
The lamination process consists of two main steps:
A computer-controlled bonding press regulates the stack-up heating, pressure application, and controlled cooling of the stack to ensure optimal bonding quality.
Sierra Circuits specializes in high-precision PCB manufacturing in the USA, utilizing advanced tools like X-ray drill machines, mechanical vision drill systems with controlled depth, laser drilling, and Seica FPT machines to ensure the highest precision.
Check out our rigid PCB manufacturing capabilities to learn more.
During this stage, holes are created for vias and solder leaded components. A computer-controlled X-ray drill is used to accurately locate target points within the inner layers and drill precise registration holes. Operators can select specific drill programs, allowing the machine to position itself accurately along the X-Y coordinates.
The system is capable of drilling holes as small as 125 microns in diameter. The machine automatically selects the drilling parameter for material/stack-up.
Drilling can produce burrs. These are removed during the deburring process, which cleans the surface of the board and eliminates any impurities. Laser drilling is commonly used in high-speed PCB manufacturing to create precise vias that support high-frequency signal performance.
For more, see PCB drilling explained: the dos and don’ts.
During this step, the walls of the drilled holes are made conductive through electroless copper deposition. It is a chemical process that coats both the hole walls and the panel surface with a thin layer of copper.
Here are the steps involved in the metallization process:
Download our eBook to learn how to select the right materials for your circuit boards.
This step utilizes photoresist, similar to the inner layers, but involves a positive image and follows the print-plate-etch method.
Are you interested in learning more about PCB Wet Process Solutions? Contact us today to secure an expert consultation!
The key steps are:
In this step, the holes and surface are electroplated with copper to ensure electrical connectivity between the layers of a printed circuit board.
Below are the key stages of the copper plating process:
Once the panel is plated, the photo-resist will be stripped off to expose the unwanted copper.
A single continuous process line is used to dissolve and wash off the photoresist that covers the copper areas intended for removal. This step ensures that the panel is properly prepared for the subsequent etching phase.
In this stage, the unwanted exposed copper is chemically removed using an ammoniacal etchant. The areas of copper protected by a tin layer remain intact, as the tin acts as a resist against the etching solution. This process precisely defines the conducting paths and establishes the final circuit connections on the board.
For more, see wet PCB etching using acidic and alkaline methods.
Post etching, the protective tin layer present on the copper tracks is removed. This is achieved using concentrated nitric acid, which effectively dissolves the tin without damaging the copper underneath. As a result, a clean and well-defined outline of the copper tracks becomes visible on the PCB surface.
Try our Better DFM tool to thoroughly verify design for manufacturing aspect of your PCB design.
Solder mask in PCB serves the following purposes:
The application process typically involves the LPI (liquid photo imageable) mask, which allows precise and uniform coverage across various board surfaces. Here’s an overview of the process:
This process ensures the resistive layer is accurately aligned and fully integrated with the circuit board structure.
Green became the standard solder mask color because it doesn’t strain the eyes. Before automated inspection systems were introduced, PCB inspection was done manually. The overhead lighting used by technicians did not reflect as harshly off the green mask, reducing glare and making it safer and more comfortable for extended visual inspections.
PCB surface finishes form intermetallic joints between the bare copper on the solderable areas of a circuit board and its components. The base copper is highly susceptible to oxidation without a protective coating, so applying a surface finish is essential to prevent corrosion. Additionally, the surface finish prepares the board for soldering during assembly and helps extend its shelf life.
Lead-free PCB manufacturing demands surface finishes that can withstand higher processing temperatures and meet environmental compliance standards.
There are various types of surface finishes available. However, lead-free surface finishes are widely used in PCB fabrication process due to the strict RoHS (restriction of hazardous substances) norms.
Table 1: Classification of surface finishes
Type Surface finish Description Metallic HASL (hot air solder leveling) Solder coating by dipping in molten tin-lead solder and removing excess with hot air. Lead-free HASL Variation of HASL using RoHS-compliant lead-free solder alloys like Sn/Ag/Cu. ENIG (electroless nickel immersion gold) Thin gold over nickel layer to prevent copper oxidation. ENEPIG Combination of nickel, palladium, and gold for high solderability and oxidation resistance. Hard gold Thick, durable gold plating over nickel, used in high-wear areas like edge connectors. Soft gold Primarily used for wire bond pads or where a thicker gold deposit is required. Immersion silver (ImAg) Lead-free silver coating that protects copper through an immersion reaction. Immersion tin (ImSn) Thin tin layer on copper, suitable for fine-pitch and RoHS-compliant boards. Organic OSP (organic solderability preservative) Water-based organic coating to protect copper until soldering.While choosing a surface finish, consider the factors such as cost, environment, component selection, shelf life, and production volume.
In this process, inkjet projectors are used to image the legends directly from the board’s digital data.
The ink is spread on the surface of the panel using a jet printer. The panels are then baked to cure the ink. It designates different kinds of text such as part number, name, code, logos, etc.
There are two types of silkscreen printing:
E-test refers to bare board electrical testing. In this step, electrical probes are used to check for shorts, opens, and netlist integrity.
This test verifies the electrical conductivity of the circuit board using the netlist file, which contains information about the PCB’s intended interconnection patterns.
Flying probe tests in PCB are implemented to test for functionality. The test is done using probes that move from one point to another based on instructions provided by specialized software. It is a fixtureless test method.
Initially, flying probe test (FPT) programs are created and then loaded into the FPT tester. The tester applies electrical signals and power to the probe points and measures the results according to the test program.
Circuit boards are profiled and cut out of the production panel during the final stage of the PCB manufacturing process. This is typically done using either a router or a V-scoring machine.
The V-groove method cuts diagonal channels on both sides of the board, while the router leaves small tabs along the borders. In either case, the boards can be easily popped out from the panel.
Use our Stackup Designer to quickly create a manufacturable build-up.
Don Ball has been a process engineer for Chemcut since . His duties have included the testing and development of new processing equipment as well as providing on-site technical assistance for the startup of new equipment and help in solving process problems with existing equipment for customers all over the world. He finds it amazing that there are always new and unique problems cropping up despite almost 50 years of experience.
The company is the world’s best Stencil Cleaning Machine supplier. We are your one-stop shop for all needs. Our staff are highly-specialized and will help you find the product you need.