1'What does mandrel bending mean?
You will get efficient and thoughtful service from LECN.
Mandrel bending is a method of inserting steel rods into the tube to provide support during bending. This method can bend the tube perfectly, prevent the tube from flattening, and allow the tube to be bent without wrinkles or kinks.
Not all tube bending requires a mandrel. Generally, smaller diameter tubes (such as 6-8 mm tubes) have more support on their own and do not need to use a mandrel. In addition, some galvanized pipes and iron pipes with large bending radius and thick wall thickness do not require a mandrel. However, for thin-walled tubes with a small bending radius and a large diameter, the inner wall of the tube should be supported by a mandrel to prevent its cross-section from becoming elliptical and wrinkling on the inside.
2'When mandrel is needed'
Hippo has summarized a formula based on long-term practical experience, which can help you quickly determine whether a mandrel is needed to complete the bend.
D is the outer diameter of the tube, T is the wall thickness of the tube, and R is the bending radius. The difficulty of bending a pipe depends on the wall thickness and bending radius of the pipe. The smaller the wall thickness and the smaller the radius, the more difficult it is to process.
We use relative wall thickness tx = t / D and relative bending radius Rx = R / D as the bending process parameters. For pipe fittings with Rx>3D and tx>0.04, standard tools can be used. For pipe fittings with Rx <3D and tx <0.04D, mandrels, wiper die and other technical measures can be added to ensure bending quality.
3'How to choose the right mandrel'
With mandrel bending is relatively technically difficult, how should we correctly use mandrel bending to enhance the quality of the bend?
' The first is to determine the type of mandrel.
In general, the mandrel can be divided into two categories: one is the hard mandrel and the other is the soft mandrel.
For hard mandrels, the cylindrical mandrel (or cylindrical ball-head mandrel) has a simple shape and is easy to manufacture, so it is more common than claw-shaped mandrels.
For soft mandrels, the spherical node mandrel is very flexible and can swing in any direction, and can adapt to various deformations. Therefore, the spherical node mandrel is often used when bending thin-walled or small bending radius pipes.
At the same time, we have to decide the ball joint quantity according to different relative bending radii, relative tube wall thicknesses, and bending angles. If the number of ball joints is small, the expected effect cannot be achieved; If the number is large, it is difficult to manufacture and it is not convenient for the pipe to penetrate.
' The second is to determine the size of the mandrel ball.
The gap between the mandrel and the tube's inner diameter is also an important factor affecting the quality of the bend. If the mandrel ball diameter is too small, the tube inside may occur wavy wrinkles, can't play a role in preventing the tube outside from flattening; If the diameter is large or the mandrel ball outside is not smooth enough, the tube wall would be strained, or even break.
In a word, the selection of a reasonable mandrel diameter and its adequate lubrication are indispensable elements for the quality of the bend.
You could refer to the following empirical formula: d ' (0.94 to 0.98) D to decide the mandrel ball size.
d- mandrel diameter
D- tube inner diameter size.
Are you interested in learning more about roller bender machine? Contact us today to secure an expert consultation!
' The third is to ensure the mandrel toughness and lubrication
In order to avoid scratches on the inner wall of the tube, the mandrel shall be sufficiently tough and carefully deburred and polished; the inner lumen of the tube shall also be carefully cleaned and, if necessary, wet-blown sand. The arbor should also be rigid enough to avoid creases caused by shaking, and the proper lubricant should be used.
4) How to use the mandrel correctly
The position where the mandrel penetrates into the pipe and begins to bend seriously affects the quality of the bent pipe.
If the punctured position is too far forward, the pipe outside material would be easily get stretched and can be thinner.
If the penetration position is too far back, the corresponding supporting effect cannot be achieved, and the tube easily collapses, and even wrinkles on the inside.
So, how exactly do we get this right? In fact, we can combine a formula to select: e ' (1/4 ~ 1/2) D. The letter e in the formula represents the position where the mandrel penetrates into the pipe at the beginning of bending, the letter D represents the inner diameter of the pipe. hen the specific value can be obtained by calculation.
Finally, after determining the position scale, we should first conduct a trial bend based on this value. During the trial bending process, make appropriate adjustments in accordance with the specific conditions, so that the mandrel reaches the appropriate position. In this way, the resulting bending products can be satisfying.
In addition, when bending square (rectangular) pipes, the cross-section shapes of the mold and the mandrel are different from the round steel pipe, but the selection and use of the mandrel and the bending method are basically the same.
5'Why after use mandrel, the bend still have wrinkles?
Sometimes even when a mandrel is used, wrinkles occur when the pipe is bent.
The following are six main causes of wrinkles when pipes are bent:
'The tube slides in the clamping die
'The mandrel is not far enough
'The wiper die is not installed correctly
' Wiper die is worn or not fit
'The gap between the mandrel rod and the tube is too large
'Improper or an excessive amount of lubricant
If both the mandrel and the wiper die are in place, check the pressure inside. You may need to apply more pressure on the dies to keep the tube. Slowly adjust until there are no wrinkles.
The company is the world’s best cnc cylindrical grinder manufacturer supplier. We are your one-stop shop for all needs. Our staff are highly-specialized and will help you find the product you need.